View NR6012T330ME_6641040.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

notice_e-01 notice for taiyo yuden products y please read this notice before using the taiyo yuden products. reminders product information in this catalog is as of october 2010. all of the contents speci?ed herein are subject to change withou t notice due to technical improvements, etc. therefore, please check for the latest information carefully be - fore pra c tical application or usage of the products. plea s e note that taiyo yuden co., ltd. shall not be responsible for any defects in products or equipment incorpo - ratin g such products, which are caused under the conditions other than those speci?ed in this catalog or individual speci ? cation. please contact taiyo yuden co., ltd. for further details of product speci?cations as the individual speci?cation is avail a ble. please conduct validation and veri?cation of products in actual condition of mounting and operating environment before c o mmercial shipment of the equipment. all e lectronic components or functional modules listed in this catalog are developed, designed and intended for use in g eneral electronics equipment.(for av, office automation, household, office supply, information service, telec o mmunications, (suc h as mobile phone or pc) etc.). before incorporating the components or devices into any equipment in the ?eld such as transportation,( automotive control, train control, ship control), transportation signal, disas t er prevention, medical, public information network (telephone exchange, base station) etc. which may have direc t i n?uence to harm or injure a human body, please contact taiyo yuden co., ltd. for more detail in advance. do no t incorporate the products into any equipment in ?elds such as aerospace, aviation, nuclear control, subma - rine sy s tem, military, etc. where higher safety and reliability are especially required. in ad d ition, even electronic components or functional modules that are used for the general electronic equipment, if the e quipment or the electric circuit require high safety or reliability function or performances, a suf?cient reliabil - ity ev a luation check for safety shall be performed before commercial shipment and moreover, due consideration to insta l l a protective circuit is strongly recommended at customer's design stage. the c ontents of this catalog are applicable to the products which are purchased from our sales of?ces or distribu - tors (s o c alled ? taiyo y u den ? s of?cial sales channel ? ). it is only applicable to the products purchased from any of taiyo yuden ? s of?ci a l sales channel. please note that taiyo yuden co., ltd. shall have no responsibility for any controversies or disputes that may oc - cur in c onnection with a third party's intellectual property rights and other related rights arising from your usage of produ c ts in this catalog. taiyo yuden co., ltd. grants no license for such rights. cau t ion for export cert a in items in this catalog may require speci?c procedures for export according to ? forei g n exchange and for - eign trade control law ? of ja p an, ? u.s. export administration regulations ? , and other applicable regulations. should you have any question or inquiry on this matter, please contact our sales staff.
128 wound04_e-01 features ordering code external dimensions /standard quanti ty applications this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. ? small and low pro?le inductor. ? it corresponds to high current. ? simp l e and original magnetic shield structure. ? dura b le structure against dropping impact. ? for sm a ll dc/dc converter (cell u lar phone, hdd, dvc, dsc, pda, lcd display etc). smd inductors low profile type ? type nr coating resin speci?cation blank space ? packaging t tape & reel blank space ? nominal inductance h example 2r2 2.2 100 10 101 100 r decimal point ? inductance tolerance m 20% n 30% ? internal code standard product blank space ? external dimensions (w l h) 3010 3.0 3.0 1.0mm 5040 5.0 5.0 4.0mm 3012 3.0 3.0 1.2mm 6012 6.0 6.0 1.2mm 3015 3.0 3.0 1.5mm 6020 6.0 6.0 2.0mm 4010 4.0 4.0 1.0mm 6028 6.0 6.0 2.8mm 4012 4.0 4.0 1.2mm 6045 6.0 6.0 4.5mm 4018 4.0 4.0 1.8mm 8040 8.0 8.0 4.0mm n r 4 0 1 8 t 1 0 0 m ? ? ? ? ? ? reflow type l w h e f standard quantity [pcs ] tape & reel nr3010 3.0 0.1 0.118 0.004 3.0 0.1 0.118 0.004 1.0 max 0.9 0.2 0.035 0.008 1.9 0.2 0.075 0.008 2000 0.039 max nr3012 1.2 max 2000 0.047 max nr3015 1.5 max 2000 0.059 max nr4010 4.0 0.2 4.0 0.2 1.0 max 1.1 0.2 2 . 5 0.2 5000 0.039 max nr4012 1.2 max 4500 0.047 max nr4018 0.157 0.008 0.157 0.008 1.8 max 0.043 0.008 0.098 0.008 3500 0.071 max nr8040 8.0 0.2 8.0 0.2 * 1 4.2max 1.6 0.3 5.6 0.3 1000 0.165max 0.315 0.008 0.315 0.008 * 2 4.0max 0.063 0.012 0.220 0.012 0.157max *1 0r9 6r8 type *2 100 101 type uni t : mm (inch) l w e e f h f l l w h e e type l w h e f l standard quantity [pcs ] tape & reel nr5040 4.9 0.2 0.193 0.008 4.9 0.2 0.193 0.008 3 4.1max 0.161max 4 4.0max 0.157max 1.2 0. 2 0.047 0.008 3.3 0.2 0.130 0.008 1.3 0.3 0.051 0.011 1500 nr6012 e type 6.0 0.2 6.0 0.2 1.2 max 1.35 0. 2 4 .0 0.2 2.3 0.3 0.091 0.011 1000 0.236 0.008 0.236 0.008 0.047 max 0.053 0 .008 0.157 0.008 nr6020 6.0 0.2 6.0 0.2 2.0 max 1.35 0. 2 4 .0 0.2 2500 0.236 0.008 0.236 0.008 0.078 max 0.053 0 .008 0.157 0.008 nr6028 6.0 0.2 6.0 0.2 2.8 max 1.35 0. 2 4 .0 0.2 2000 0.236 0.008 0.236 0.008 0.110 max 0.05 3 0.008 0.157 0.008 nr6045 6.0 0.2 6.0 0.2 4.5 max 1.35 0. 2 4 .0 0.2 1500 0.236 0.008 0.236 0.008 0.177 max 0.053 0 .008 0.157 0.008 *3 1r5 100type *4 150 470type unit : mm (in ch) operating temp. ? ` 25 120 includ ing self-generated heat
ferrite products 129 wound04_e-01 available inductance range part numbers nr 3010 shielded type nr 3012 sh ielded type ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 2 0 ) rate d c urrent ma meas u ring frequ e ncy khz saturation current idc1 temperature rise current idc2 nr 3010t 1r0n rohs 1.0 30 126 0. 0 65 1,300 1, 400 100 nr 3010t 1r5n rohs 1.5 98 0.08 0 1 ,200 1, 300 nr 3010t 2r2m rohs 2.2 20 82 0.095 1,100 1 , 100 nr 3010t 3r3m rohs 3.3 63 0.140 870 940 n r 3010t 4r7m rohs 4.7 56 0.190 750 780 nr 3010t 6r8m rohs 6.8 46 0.300 610 630 n r 3010t 100m rohs 10 35 0.450 500 510 n r 3010t 150m rohs 15 30 0.740 400 400 n r 3010t 220m rohs 22 25 1.03 350 350 n r 3010t 330m rohs 33 20 1.55 260 275 n r 3010t 470m rohs 47 17 2.05 220 235 ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 2 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 3012t 1r0n rohs 1.0 30 110 0. 0 50 1,500 1, 490 100 nr 3012t 1r5n rohs 1.5 92 0.06 0 1 ,360 1, 400 nr 3012t 2r2m rohs 2.2 20 70 0.080 1,100 1 , 200 nr 3012t 3r3m rohs 3.3 55 0.100 910 1,0 5 0 nr 3012t 4r7m rohs 4.7 48 0.130 770 980 n r 3012t 6r8m rohs 6.8 40 0.190 670 740 n r 3012t 100m rohs 10 32 0.290 540 630 n r 3012t 150m rohs 15 27 0.450 440 485 n r 3012t 220m rohs 22 22 0.630 375 420 n r 3012t 330m rohs 33 19 1.03 310 330 n r 3012t 470m rohs 47 17 1.45 250 280 this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. nr 3015 shielded type ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 2 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 3015t 1r0n rohs 1.0 30 100 0. 0 30 2,100 2, 100 100 nr 3015t 1r5n rohs 1.5 87 0.04 0 1 ,800 1, 820 nr 3015t 2r2m rohs 2.2 20 64 0.060 1,480 1 , 500 nr 3015t 3r3m rohs 3.3 49 0.080 1,210 1 , 230 nr 3015t 4r7m rohs 4.7 40 0.120 1,020 1 , 040 nr 3015t 6r8m rohs 6.8 36 0.160 870 880 n r 3015t 100m rohs 10 28 0.230 700 710 n r 3015t 150m rohs 15 23 0.360 560 560 n r 3015t 220m rohs 22 20 0.520 470 470 n r 3015t 330m rohs 33 18 0.840 390 370 n r 3015t 470m rohs 47 17 1.34 320 300 the saturation current value (idc1) is the dc current value having inductance decrease down to 30%. (at 20 ) the temperature rise current value idc2) i s the dc current value having temperature increase up to 40 . (at 20 ) the rated current is the dc current value that satis?es both of current value saturation current value and temperature rise current value. recomm ended land pa t terns unit : mm 0.8 2.7 2.2 0.8 2 nr3010, nr3012, nr3015 3 2.8 1.2 3.7 1.2 2 nr4010, nr4012, nr4018 3 1.6 1.6 5.7 2 nr6012,nr6020,nr6028,nr6045 3 4.7 1.5 1.5 4.0 2 nr5040 3 3.6 1.8 7.5 1.8 2 nr8040 3 5.6 range type nr 3010 nr 3012 nr 3015 nr 4 010 nr 4 012 nr 4 018 nr 5 040 nr 6 012 nr 6 020 nr 6 028 nr 6 045 nr 8 040 0. 8 imax [ma] rdc 20 ?? imax [ma] rdc 20 ?? imax [ma] rdc 20 ?? imax [ma] rdc 20 ?? imax [ma] rdc 20 ?? imax [ma] rdc 20 ?? imax [ma] rdc 30 ?? imax [ma] rdc 20 ?? imax [ma] rdc 20 ?? imax [ma] rdc 30 ?? imax [ma] rdc 30 ?? imax [ma] rdc 30 ?? 1.0 1300 0.065 1490 0.05 2100 0.030 1050 0.100 1500 0.060 1830 0.030 3800 0.020 4600 0.013 4200 0.014 7800 0.006 3.3 500 0.450 540 0.290 700 0.230 560 0.380 740 0.240 840 0.180 3600 0.020 1730 0.090 1400 0.125 1900 0.065 2500 0.047 3100 0.034 10 2100 0.056 1000 0.235 47 220 2.05 250 1.45 300 1.34 240 1.81 350 1.00 900 0.310 950 0.290 100 220 170 4.00 320 2.18 620 0.600 700 0.500 1000 0.290 inductance ? h
130 wound04_e-01 part numbers this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. nr 4018 shielded type nr 6012 shielded type nr 4012 s h ielded type ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resis tance [ ] ( 2 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 4012t 1r0n rohs 1.0 30 131 0. 0 60 2,500 1, 500 100 nr 4012t 2r2m rohs 2.2 20 66 0.0 9 0 1,650 1, 200 nr 4012t 3r3m rohs 3.3 50 0.130 1,200 9 8 0 nr 4012t 4r7m rohs 4.7 45 0.140 1,050 9 6 0 nr 4012t 6r8m rohs 6.8 35 0.180 900 840 n r 4012t 100m rohs 10 28 0.240 740 770 n r 4012t 150m rohs 15 23 0.400 560 600 n r 4012t 220m rohs 22 18 0.480 510 540 n r 4012t 330m rohs 33 15 0.810 400 420 n r 4012t 470m rohs 47 12 1.00 350 370 ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resis tance [ ] ( 2 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 4018t 1r0n rohs 1. 0 30 80 0.03 0 4,000 1, 830 100 nr 4018t 2r2m rohs 2. 2 20 52 0.06 0 2,700 1, 440 nr 4018t 3r3m rohs 3. 3 4 4 0.070 2,000 1, 230 nr 4018t 4r7m rohs 4. 7 3 4 0.090 1,700 1, 200 nr 4018t 6r8m rohs 6. 8 2 9 0.110 1,450 1, 060 nr 4018t 100m rohs 10 2 4 0 .180 1,200 84 0 nr 4018t 150m rohs 15 1 9 0 .250 940 650 nr 4018t 220m rohs 22 1 6 0 .360 800 590 nr 4 018t 330m rohs 33 1 2 0 .530 650 490 nr 4018t 470m rohs 47 1 0 0 .650 570 420 nr 4 018t 680m rohs 68 8 . 3 1.00 470 3 20 nr 4018t 101m rohs 10 0 6 .5 1.50 400 2 70 nr 4 018t 151m rohs 15 0 5 .5 2.50 310 2 20 nr 4018t 221m rohs 22 0 4 .0 4.00 270 1 70 ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 2 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 6012t 2r5ne rohs 2. 5 3 0 45 0.09 0 2,100 1, 730 100 nr 6012t 4r0ne rohs 4. 0 39 0.105 1 ,800 1, 570 nr 6012t 5r3me rohs 5. 3 2 0 34 0.125 1,500 1, 400 nr 6012t 6r8me rohs 6. 8 3 0 0.165 1,300 1, 180 nr 6012t 100me rohs 10 2 2 0 .235 1,000 1, 000 nr 6012t 150me rohs 15 1 8 0 .330 800 790 nr 6 012t 220me rohs 22 1 2 0 .530 760 630 nr 6 012t 330me rohs 33 8 0 . 700 590 530 nr 6 012t 470me rohs 47 6 1 . 05 520 460 nr 6012t 680me rohs 68 3 1 . 35 440 410 nr 6012t 101me rohs 10 0 1 2 .18 350 320 the saturation current value (idc1) is the dc current value having inductance decrease down to 30%. (at 20 ) the temperature rise current value (idc2) is the dc current value having temperature increase up to 40 . (at 20 ) th e rated current is the dc current value that satis?es both of current value saturation current value and temperature rise current value. nr 4010 shielded type ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 2 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 4010t 1r0n rohs 1.0 30 116 0. 1 00 1,800 1, 050 100 nr 4010t 2r2n rohs 2.2 73 0.15 0 1 ,150 89 0 nr 4010t 3r3m rohs 3.3 20 58 0.180 1,100 8 2 0 nr 4010t 4r7m rohs 4.7 47 0.210 900 750 n r 4010t 6r8m rohs 6.8 38 0.300 740 620 n r 4010t 100m rohs 10 31 0.380 560 600 n r 4010t 150m rohs 15 24 0.510 470 510 n r 4010t 220m rohs 22 19 0.870 360 400 n r 4010t 330m rohs 33 15 1.54 280 300 n r 4010t 470m rohs 47 13 1.81 240 280 nr 5040 shielded type ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 3 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 5040t 1r5n rohs 1. 5 30 60 0.02 0 6,000 3, 600 100 nr 5040t 2r2n rohs 2. 2 42 0.022 4 ,600 3, 500 nr 5040t 3r3n rohs 3. 3 32 0.027 3 ,800 3, 300 nr 5040t 4r7n rohs 4. 7 28 0.029 3,300 3, 100 nr 5040t 6r8m rohs 6. 8 20 21 0.04 9 2,600 2, 300 nr 5040t 100m rohs 10 1 8 0 .056 2,300 2, 100 nr 5040t 150m rohs 15 1 3 0.080 2,000 1, 800 nr 5040t 220m rohs 22 9 0 .126 1 ,600 1, 400 nr 5040t 330m rohs 33 7 0 . 180 1 ,300 1, 200 nr 5040t 470m rohs 47 6 0 . 310 1 ,100 90 0
ferrite products 131 wound04_e-01 this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. part numbers nr 6020 shielded type nr 6028 sh ielded type ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 2 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 6020t 0r8n rohs 0. 8 3 0 110 0.020 5,500 3, 800 100 nr 6020t 1r5n rohs 1. 5 93 0.026 4 ,000 3, 200 nr 6020t 2r2n rohs 2. 2 7 3 0.034 3,200 2, 700 nr 6020t 3r3n rohs 3. 3 5 5 0.040 2,800 2, 600 nr 6020t 4r7n rohs 4. 7 4 3 0.058 2,400 2, 000 nr 6020t 6r8n rohs 6. 8 3 0 0.085 2,000 1, 800 nr 6020t 100m rohs 10 2 0 1 8 0.125 1,700 1, 400 nr 6020t 220m rohs 22 1 1 0 .290 1,050 95 0 ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resis tance [ ] ( 3 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 6028t 0r9n rohs 0. 9 3 0 90 0.01 3 6,600 4, 600 100 nr 6028t 1r5n rohs 1. 5 78 0.016 5 ,000 4, 200 nr 6028t 2r2n rohs 2. 2 6 8 0.020 4,200 3, 700 nr 6028t 3r0n rohs 3. 0 5 5 0.023 3 ,600 3, 400 nr 6028t 4r7m rohs 4. 7 2 0 39 0.031 2,700 3, 000 nr 6028t 6r0m rohs 6. 0 3 0 0.040 2 ,500 2, 500 nr 6028t 100m rohs 10 2 0 0 .065 1,900 1, 900 nr 6028t 150m rohs 15 1 7 0 .095 1,600 1, 800 nr 6028t 220m rohs 22 1 2 0 .135 1,300 1, 400 nr 6028t 330m rohs 33 1 0 0 .220 1,100 1, 100 nr 6028t 470m rohs 47 8 0 . 300 950 920 nr 6 028t 680m rohs 68 5 0 . 420 760 770 nr 6028t 101m rohs 10 0 3 0 .600 620 660 nr 6045 shielded type nr 8040 sh ielded type ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 3 0 ) rate d c urrent ma meas u ring frequ e ncy khz saturation current idc1 temperature rise current idc2 nr 6045t 1r0n rohs 1. 0 30 110 0.0 14 8,500 4, 200 100 nr 6045t 1r3n rohs 1. 3 95 0.016 8,000 4, 000 nr 6045t 1r8n rohs 1. 8 80 0.018 7,000 3, 700 nr 6045t 2r3n rohs 2. 3 6 0 0.021 6 ,000 3, 500 nr 6045t 3r0n rohs 3. 0 4 5 0.024 5,000 3, 200 nr 6045t 4r5m rohs 4. 5 20 25 0.03 1 4,000 3, 000 nr 6045t 6r3m rohs 6. 3 15 0.038 3 ,800 2, 800 nr 6045t 100m rohs 10 1 2 0.047 3 ,000 2, 500 nr 6045t 150m rohs 15 1 0 0.077 2 ,300 1, 900 nr 6045t 220m rohs 22 7 0 .115 1, 900 1, 500 nr 6045t 330m rohs 33 6 0 . 145 1, 500 1, 400 nr 6045t 470m rohs 47 5 0 . 220 1, 300 1, 100 nr 6045t 680m rohs 68 4 0 .330 1, 000 90 0 nr 6045t 101m rohs 10 0 3 0.500 80 0 700 ordering code ehs ( environmental hazardous substances ) inductance [ h] inductance toler a nce self-resonant frequ e ncy mhz (min.) dc resi s tance [ ] ( 3 0 ) rate d c urrent ma meas u ring freque ncy khz saturation current idc1 temperature rise current idc2 nr 8040t 0r9n rohs 0.9 30 85 0.0 0 6 11,000 7 ,800 100 nr 8040t 1r4n rohs 1.4 63 0.00 7 9,000 7, 000 nr 8040t 2r0n rohs 2.0 50 0.00 9 7 ,400 6, 300 nr 8040t 3r6n rohs 3.6 34 0.01 5 5 ,300 4, 900 nr 8040t 4r7n rohs 4.7 30 0.01 8 4 ,700 4, 100 nr 8040t 6r8n rohs 6.8 24 0.02 5 4 ,000 3, 700 nr 8040t 100m rohs 10 20 22 0.0 3 4 3,400 3, 100 nr 8040t 150m rohs 15 16 0.05 0 2 ,700 2, 400 nr 8040t 220m rohs 22 13 0.06 6 2,200 2, 200 nr 8040t 330m rohs 33 12 0.10 0 1 ,900 1, 700 nr 8040t 470m rohs 47 8 0.150 1 , 500 1, 400 nr 8040t 680m rohs 68 7 0.230 1 ,200 1, 100 nr 8040t 101m rohs 100 6 0.290 1 , 000 1, 000 the saturation current value (idc1) is the dc current value having inductance decrease down to 30%. (at 20 ) the temperature rise current value (idc2) is the dc current value having temperature increase up to 40 . (at 20 ) th e rated current is the dc current value that satis?es both of current value saturation current value and temperature rise current value.
132 wound04_e-01 electrical characteristics this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. measured by hp4285a dc bias characteristics 100 10 1 10 100 1,000 10,000 nr 3010 dc bias ma inductance h 220m 470m 100m 4r7m 2r2m 100 10 1 10 100 1,000 10,000 nr 4012 dc bias ma inductance h 470m 220m 100m 2r2m 4r7m 1 1.0 01 1000 100 nr 6028 10 100 1,000 10,000 dc bias ma inductance h 220m 100m 470m 101m 2r2 4r7 0r9 1 10 100 n nr 5040 10 100 1,000 10,000 dc bias ma inductance h 220m 100m 470m 2r2n 4r7n 1000 100 10 1 10 100 1,000 10,000 nr 4018 dc bias ma inductance h 470m 101m 221m 220m 100m 2r2m 4r7m 1000 100 10 1 0.1 10 100 1,000 10,000 100,000 nr 6045 dc bias ma inductance h 220m 100m 470m 101m 2r3n 4r5n 1r0n 1000 100 10 1 10 100 1,000 10,000 nr 6012 e type dc bias ma inductance h 220m 470m 101m 100m 5r3m 1000 100 10 1 0.1 10 100 1,000 10,000 100,000 nr 8040 dc bias ma inductance h 220m 100m 470m 101m 2r0n 4r7n 0r9n 1 1.0 01 001 nr 6020 10 100 1,000 10,000 dc bias ma inductance h 220m 100m 4r7m 2r2m 0r8n 100 10 1 10 100 1,000 10,000 nr 3012 dc bias ma inductance h 220m 470m 100m 4r7m 2r2m 100 10 1 10 100 1,000 10,000 nr 3015 dc bias ma inductance h 220m 470m 100m 4r7m 2r2m 100 10 1 10 100 1,000 10,000 nr 4010 dc bias ma inductance h 470m 220m 100m 2r2n 4r7m
ferrite products 133 wound04_e-01 this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs.
wound0405_pack-p1 wound0405_pack_e-01 packaging this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. ? embossed tape 8mm wide (0.315 inches wide) minimu m quant i ty chip cavity 1.5 0.059 1.75 ? 0.1 0.069 ? 0.004 4.0 ? 0.1 0.157 ? 0.004 2.0 ? 0.05 0.079 ? 0.002 3.5 ? 0.1 0.138 ? 0.004 8.0 ? 0.2 0.315 ? 0.008 k t f a 0.1 ? 0 0.004 ? 0 b electrode bottom view position of wire tape material taping dimensions leader and blank portion type chip cavity insertion pitch tape thickness a b f t k nrs 8030 8.3 0.1 0.327 0.004 8.3 0.1 0.327 0.004 12.0 0.1 0.472 0.004 0.5 0.1 0.020 0.004 3.4 0.1 0.134 0.004 nr 8040 nrs 804 0 4.5 0.1 0.177 0.004 unit : mm (inch) ? embossed tape 12mm wide (0.47 inches wide) ? emboss ed tape 16mm wide (0.63 i n ches wide) chip cavity 1.5 0.059 1.75 ? 0.1 0.069 ? 0.004 4.0 ? 0.1 0.157 ? 0.004 2.0 ? 0.1 0.079 ? 0.004 5.5 ? 0.1 0.217 ? 0.004 12.0 ? 0.3 0.472 ? 0.012 k t f a 0.1 ? 0 0.004 ? 0 b electrode bottom view position of wire k t b chip cavity f a 2.0?0.1 0.079?0.004 1.5?0.1 0.059?0.004 4.0?0.1 0.157?0.004 1.75?0.1 0.069?0.004 7.5?0.1 0.295?0.004 16.0?0.3 0.630?0.012 electrode bottom view position of wire 100mm or more (3.94 inches or more) 400mm or more (15.8 inches or more) blank portions blank portions chip cavity leader direction of tape feed 160mm or more (6.3 inches or more) ? nr, nrh, nrs, nrg, nrv type standard quantity [ pcs ] tape reel nrh24 1 0 2500 nr 3010/nrh3010 2000 nr 3 012/nrh3012/nrv3012 2000 nr 3 0 15 2000 nr 4 010/nrs4010 5000 nr 4 0 12/nrs4012 4500 nr 4 0 18/nrs4018 3500 nr g 4026 2000 nrs5012 1000 nrs5014 1000 nrs5020 800 nr 5040 1500 nrs 6010 1000 nr 6012/nrs6012 1000 nr 6 020/nrs6020 2500 nr 6 0 28/nrs6028 2000 nr 6 0 45/nrs6045 1500 nr s 8030 1000 nr 8040/nrs8040 1000 type chip cavity insertion pitch tape thickness a b f t k nrh 2410 2.6 0.1 2.6 0.1 4.0 0.1 0.157 0.004 0.25 0.05 1.3 0.1 0.102 0.004 0.102 0.004 0.009 0.002 0.051 0.004 nr 3010 nrh 3010 3.2 0.1 0.126 0.004 3.2 0.1 0.126 0.004 0.3 0.05 0.012 0.002 1.4 0.1 0.055 0.004 nr 3012 nrh 3012 nrv3012 1.6 0.1 0.063 0.004 nr 3015 1.9 0.1 0.075 0.004 unit : mm (inch) type chip cavity insertion pitch tape thickness a b f t k nr 4010 nrs 4010 4.3 0.1 (0.169 0.004) 4.3 0.1 (0.169 0.004) 8.0 0.1 0.315 0.004 0.3 0.05 0.012 0.002 1.4 0.1 (0.055 0.004) nr 4012 nrs 401 2 1.6 0.1 (0.063 0.004) nr 4018 nrs 401 8 2.1 0.1 (0.083 0.004) nrg 4026 3.1 0.1 (0.122 0.004) nrs 5012 5.25 0.1 (0.207 0.004) 5.25 0.1 (0.207 0.004) 1.4 0.1 (0.055 0.004) nrs 5014 1.6 0.1 (0.063 0.004) nrs 5020 2.3 0.1 (0.091 0.004) nr 5040 5.15 0.1 (0.203 0.004) 5.15 0.1 (0.203 0.004) 0.4 0.1 (0.016 0.004) 4.2 0.1 (0.165 0.004) nrs 6010 6.3 0.1 (0.248 0.004) 6.3 0.1 (0.248 0.004) 1.4 0.1 (0.055 0.004) nr 6012 nrs 601 2 1.6 0.1 (0.063 0.004) nr 6020 nrs 602 0 2.3 0.1 (0.090 0.004) nr 6028 nrs 602 8 3.1 0.1 (0.122 0.004) nr 6045 nrs 604 5 4.7 0.1 (0.185 0.004) unit : mm (inch)
wound0405_pack-p2 wound0405_pack_e-01 packaging this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. 13 ? 0.5 w d d 2 ? 0.5 2.5 or less 0.098inches or less reel size top tape strength 13 ? 0.5 w t d d 2 ? 0.5 the top tape requires a peel-off force of 0.1 to 1.3n in the direction of the arrow as illustrated below. type reel size (reference values) d d w nrh2410 180 0.5 7.087 0.019 60 1.0 2.36 0.04 10.0 1.5 0.394 0.059 nr 3010 nrh 301 0 n r 3012 n r h 301 2 n rv 301 2 n r 3015 n r s 501 2 1 80 3.0 7 .087 0.118 60 2.0 2.36 0.08 14.0 1.5 0.551 0.059 nrs 5014 nrs 502 0 n rs 601 0 n r 6012 n r s 601 2 unit : mm (inch) type reel size (reference values) d d t (max.) w nr 4010 nrs 401 0 3 30 3.0 1 2.99 0.118 80 2.0 3.15 0.07 8 18.5 0 . 72 13.5 1.0 0.531 0.04 nr 4012 nrs 401 2 n r 4018 n r s 401 8 n rg 402 6 n r 5040 n r 6 020 n r s 602 0 n r 6028 n r s 602 8 n r 6045 n r s 604 5 n rs 803 0 2 2.5 0 . 89 17.5 1.0 0.689 0.04 nr 8040 nrs 804 0 unit : mm (inch)
wound0407_reli-rp1 wound0407_reli_e-01 reliability data this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. 1. operating temperature range nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type ` 25 1 20 nr10050 type ` 25 105 ns12555, ns12565, ns12575type ` 40 125 test method and remarks inclu d ing self-generated heat 3. rated current nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type wi t hin the speci?ed tolerance nr100 5 0 type ns12555, ns12565, ns12575type 4. inductance nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type wi t hin the speci?ed tolerance nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks lcr meter : hp 4285a or equivalent, measuring frequency : speci?ed frequency nr30/ 40 /50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type, ns12555, ns12565, ns12575type : lcr meter : hp 4285a or equivalent, 100khz, 1v nr10050 type : lcr me t er : hp 4263a or equivalent, 100khz, 1v 5. dc resistance nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type wi t hin the speci?ed tolerance nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks dc ohmmeter : hioki 3227 or equivalent 6. self resonance frequency nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type wi t hin the speci?cation nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks nr30/40/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, nr10050 type, ns12555, ns12565, ns12575type : inpedance analy z er/material analyzer : hp4291a or equivalent hp4191a, 4192a or equivalent 2. storage temperature range nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type ` 40 8 5 nr10050 type ns12555, ns12565, ns12575type test method and remarks nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type, nr10050 type, ns12555, ns12565, ns12575type : 5 to 40 for the product with taping. 7. temperature characteristic nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance change : within 20% nr10050 type ns12555, ns12565, ns12575type inductance change : within 15% test method and remarks nr30/ 4 0/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, nr10050 type : measurement of inductance shall be taken at temperature range within 25 85 . with refer e nce to inductance value at 20 ., change rate shall be calculated. ns12555, ns12565, ns12575type : measu r ement of inductance shall be taken at temperature range within 40 125 . with refer e nce to inductance value at 20 ., change rate shall be calculated. change of maximum inductance deviation in step 1 to 5 temperature at step 1 20 temperature at step 2 minimum operating temperature temperature at step 3 20 (standard temperature) temperature at step 4 maximum oparating temperature temperature at step 5 20 8. resistance to ?exure of substrate nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type no d a mage nr100 5 0 type ns12555, ns12565, ns12575type no damage test method and remarks nr30/ 4 0/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, ns12555, ns12565, ns12575type : the test samples shall be soldered to the test board by the re?ow. as illustrated below, apply force in the direction of the arrow indicating until de?ection of the test board reach e s to 2 mm. test b o ard size : 100 40 1.0 t e st board material : glass epoxy-resin sold e r cream t h ickness : 0.10 (nr30/40, nrs40, nrh24/30, nrv30 ) 0.15 (nr50 / 60/80, nrs40/50/60, ns12555, ns12565, ns12575type ) force rod board test sample 20 10 r230 r5 45 ? 2mm 45 ? 2mm land dimension nrh24 0.7 0.7 0.75 2.0 land dimension nr30, nrh30, nrv30 0.8 0.81.4 2.7 land dimension nr40, nrs40 1.2 1.21.6 3.7 land dimension nr50, nrs50 1.5 1.52.1 4.0 land dimension nr60, nrs60 1.6 1.63.1 5.7 land dimension nr80 1.8 1.83.8 7.5 land dimension >?>?>?>?>?>?>?>>?>?>?>?>?>>?>>?>?>?>?>?>>? 2.5 2.58.6 3.2 unit : mm wound chip power inductor nr, ns-series
wound0407_reli-rp2 wound0407_reli_e-01 reliability data this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. 12. adhesion of terminal electrode nr30/40/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type sh a ll not come off pc board nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks nr30/4 0/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, ns12555, ns12565, ns12575 type : the test samples shall be soldered to the test board by the re?ow. ? appli e d force : 10n to x a n d y directions. ? duration : 5s. ? so l der cream thickness : 0.15mm. 10n, 5s nr10050 type : ? applied force : 5n to x and y directions. ? durati on : 5s. 9. insulation resistance : between wires nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type nr 1 0050 type ns12555, ns12565, ns12575type 10. insulation resistance : between wire and core nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type nr 1 0050 type ns12555, ns12565, ns12575type 11. withstanding voltage : between wire and core nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type nr 1 0050 type ns12555, ns12565, ns12575type 13. resistance to vibration nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance chang e : within 10% no signi?cant abnormality in appearance. nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks nr30/40/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, nr10050 type, ns12555, ns12565, ns12575type : the test samples shall be soldered to the test board by the re?ow. then i t s hall be submitted to below test conditions. frequency range 10 55hz total amplitude 1.5mm (may not exceed acceleration 196m/s 2 ) sweeping method 10hz to 55hz to 10hz for 1min. time x for 2 hours on each x, y, and z axis. y z recovery : at least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 15. resistance to soldering heat nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance chang e : within 10% no signi?cant abnormality in appearance. nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks nr30/40/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, nr10050 type, ns12555, ns12565, ns12575 type : the test sample shall be exposed to re?ow oven at 230 5 for 40 s e conds, with peak temperature at 260 5 for 5 seconds, 2 times. nr6020 type : the te s t sample shall be exposed to re?ow oven at 230 5 for 40 s e conds, with peak temperature at 250 5 ` 0 for 5 seconds, 2 times. test board thickness : 1.0mm nr30 / 40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type, ns12555, ns12565, ns12575 type 1.6mm nr10 0 50 type test board material : glass epoxy-resin 14. solderability nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type at l e ast 90 of sur f ace of terminal electrode is covered by new solder. nr10050 type ns12555, ns12565, ns12575type test method and remarks the test samples shall be dipped in ?ux, and then immersed in molten solder as shown in below table. flux : methanol solution containing rosin 25%. nr30/ 4 0/50/60/80, nrv30, n rh24/30, nrs40/50/60/80 type, ns12555, ns12565, ns12575 type : solder temperature 245 5 time 5 1.0 sec. immersion depth : all sides of mounting terminal shall be immersed. wound chip power inductor nr, ns-series
wound0407_reli-rp3 wound0407_reli_e-01 reliability data this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. 16. thermal shock nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance chang e : within 10% no signi?cant abnormality in appearance. nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks nr30/40/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, nr10050 type , ns12555, ns12565, ns12575type : the test samples shall be soldered to the test board by the re?ow. the test samples shall be placed at speci?ed temperature for speci?ed time by step 1 to step 4 as shown in belo w t able in sequence. the temperature cycle shall be repeated 100 cycles. conditions of 1 cycle step temperature ( ) duration (min) 1 ` 40 3 30 3 2 room temperature within 3 3 85 2 30 3 4 room temperature within 3 17. damp heat nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance chang e : within 10% no signi?cant abnormality in appearance. nr100 5 0 type ns12555, ns12565, ns12575type inductance change : within 10% no signi?cant abnormality in appearance. test me t hod and remarks nr30/ 4 0/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, ns12555, ns12565, ns12575type : the test samples shall be soldered to the test board by the re?ow. the te s t samples shall be placed in thermostatic oven set at speci?ed temperature and humidity as shown in below table. temperature 60 2 humidity 90 95%rh time 500 24/ 0 hour 20. high temperature life test nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type nr 1 0050 type induc t ance chang e : within 10% no signi?cant abnormality in appearance. ns12555, ns12565, ns12575type test method and remarks nr10050 type : temperature 105 3 time 500 24/ 0 hour recovery : at least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs. 21. loading at high temperature life test nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance chang e : within 10% no signi?cant abnormality in appearance. nr100 5 0 type ns12555, ns12565, ns12575type inductance change : within 10% no signi?cant abnormality in appearance. test me t hod and remarks nr30/ 4 0/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type, ns12555, ns12565, ns12575type : the test samples shall be soldered to the test board by the re?ow soldering. temperature 85 2 applied current rated current time 500 24/ 0 hour 19. low temperature life test nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance chang e : within 10% no signi?cant abnormality in appearance. nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks nr30/40/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type , nr10050 type, ns12555, ns12565, ns12575type : the test samples shall be soldered to the test board by the re?ow. afte r t hat, the test samples shall be placed at test conditions as shown in below table. temperature 40 2 time 500 24/ 0 hour 18. loading under damp heat nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type in d uctance chang e : within 10% no signi?cant abnormality in appearance. nr100 5 0 type ns12555, ns12565, ns12575type test method and remarks nr30/40/50/60/80, nrv30 , n rh24/30, nrs40/50/60/80 type , nr10050 type , ns12555, ns12565, ns12575type : the test samples shall be soldered to the test board by the re?ow. the te s t samples shall be placed in thermostatic oven set at speci?ed temperature and humidity and applied the rated current continuously as shown in below table. temperature 60 2 humidity 90 95 rh applied current rated current time 500 24/ 0 hour wound chip power inductor nr, ns-series
wound0407_reli-rp4 wound0407_reli_e-01 reliability data this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. 22. standard condition nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type st a ndard test condition : unle s s otherwise speci?ed, temperature is 20 15 and 6 5 2 0 of relative humidity. when there is any question concerning measurement result: in order to provide correlation data, the test shall be condition of 20 2 of tem p erature, 65 5% rela t ive humidity. inductance is in acc o rdance with our measured value. nr10050 type ns12555, ns12565, ns12575type wound chip power inductor nr, ns-series
wound0407_reli-rp5 wound0407_reli_e-01 precautions this catalog contains the typical speci?cation only due to the limitation of space. when you consider the purchase of our products, please check our speci?cation. for details of each product (characteristics graph, reliability information, precautions for use, and so on), see our web site (http://www.ty-top.com/) or cd catalogs. 1. circuit design precautions operating enviro nment 1. the products described in this speci?cation are intended for use in general electronic equipment,(of?ce supply equipment, telecommunications systems, measu r ing equipment, and household equipment). they are not intended for use in mission-critical equipment or systems requiring special quality and high relia b ility (traf?c systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where produ c t failure might result in loss of life, injury or damage. for such uses, contact taiyo yuden sales department in advance. 2. pcb design precautions land pattern design 1. pl e ase refer to a recommended land pattern. techn i cal consi d er - ations land pattern design surf a ce mounting ? moun t ing and sol d ering conditions should be checked beforehand. ? applicable solde r ing process to this products is re?ow soldering only. 3. considerations for automatic placement precautions adjustment of moun t ing machine 1. excessive impact load should not be imposed on the products when mounting onto the pc boards. 2. mo u nting and soldering conditions should be checked beforehand. techn i cal consi d er - ations adjustment of moun t ing machine 1. when installing products, care should be taken not to apply distortion stress as it may deform the products. 4. soldering precautions re?ow soldering 1. pl e ase contact any of our of?ces for a re?ow soldering, and refer to the recommended condition speci?ed. 2. th e p roduct shall be used re?ow soldering only. 3. pl e ase do not add any stress to a product until it returns in normal temperature after re?ow soldering. lead fr e e soldering 1. wh e n using products with lead free soldering, we request to use them after con?rming adhesion, temperature of resistance to soldering heat, soldering etc suf?c i ently. recommended condit ions for using a soldering iron (nr10050 type) ? put the soldering iron on the land-pattern. ? sold e ring iron' s t emperature - below 350 ? duration - 3 secon d s or less ? the soldering iron should not directly touch the inductor. techn i cal consi d er - ations re?ow soldering 1. if products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ? nr30/40/50/60/80, nrv30, nrh24/30, nrs40/50/60/80 type, nr10050, ns12555, ns12565, ns12575 type recommended re?ow c o ndition (pb free solder) 5sec max temperature |? 300 200 100 0 90 ? 30sec 150 ? 180 30 ? 10sec 230? min peak 250 5/ ? 0? eating time 2 sec 3 5. cleaning precautions cleaning condi t ions 1. washing by supersonic waves shall be avoided. techn i cal consi d er - ations cleaning condi t ions 1. if washed by supersonic waves, the products might be broken. 6. handling precautions handling 1. keep the product away from all magnets and magnetic objects. break a way pc boar d s (splitting along perforations) 1. when splitting the pc board after mounting product, care should be taken not to give any stresses of de?ection or twisting to the board. 2. bo a rd separation should not be done manually, but by using the appropriate devices. mecha n ical consi d erations 1. please do not give the product any excessive mechanical shocks. 2. pl e ase do not add any shock and power to a product in transportation. pick- u p pressure 1. pl e ase do not push to add any pressure to a winding part. please do not give any shock and push into a ferrite core exposure part. packi n g 1. please avoid accumulation of a packing box as much as possible. techni cal consid er - ations breakaway pc boar d s (splitting along perforations) 1. the position of the product on pcbs shall be carefully considereed to minimize the stress caused from splitting of the pcbs. mecha n ical consi d erations 1. there is a case to be damaged by a mechanical shock. 2. th e re is a case to be broken by the handling in transportation. pick- u p pressure 1. da m age and a characteristic can vary with an excessive shock or stress. packi n g 1. if packing boxes are accumulated, that could cause a deformation on packing tapes or a damage on the products. 7. storage conditions precautions storage 1. to maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be contr olled. ? rec o mmended condi t ions ambient tempe r ature : 5 40 humidity : belo w 7 0% rh the ambient temperature must be kept below 30 . even u nder ideal storage conditions, solderability of products electrodes may decrease as time passes. for this reason, product should be used within 6 months from the time of delivery. in ca s e of storage over 6 months, solderability shall be checked before actual usage. techn i cal consi d er - ations storage 1. under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of tapin g /packaging materials may take place. wound chip power inductor nr, ns-series

▲Up To Search▲

Price & Availability of NR6012T330ME

	To Download NR6012T330ME Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .